Tubes - Plumbing. Water Reticulation. Maksal. Working. Pressure. Economical(MPa)Max(mm)Min(mm)1. Best Software Synths For Psytrance. Economical. A hard drawn thin walled tube for use without bending. Recommended for use with capillary soldered fittings in above ground installations only.

1. Maksal Tubes (Pty) Ltd is South Africa's leading manufacturer of Copper tubing and Copper busbar, extrusions and profiles.
2. Using compression fittings instead of solder sweat fittings.
3. Information about plumbing with PEX tubing. How to connect PEX pipe, use PEX tools, make connections with PEX fittings.
4. Vinidex PE pipe is manufactured in sizes ranging from 16mm to 1200mm and can be jointed using a variety of techniques and fittings systems. Philmac compression.
5. To tackle a do-it-yourself plumbing project, you need to know how to recognize different types of pipes. Recognizing the different types of pipes within your house is.

The tube is identified by black end caps, and markings. Working. Pressure.

Class 0(MPa)Max(mm)Min(mm)1. Class OA hard drawn thin walled tube for use without bending. Recommended for use with capillary soldered fittings in above ground installations only. The tube is identified by translucent end caps, and markings. Working. Pressure. Class 1(MPa)Max(mm)Min(mm)1. Class 1. A thin walled tube in half hard condition which should be bent only with.

Recommended for use with both capillary soldered and compression fittings. The tube is identified by orange end caps, and markings every. Working. Pressure. Class 2(MPa)Max(mm)Min(mm)1. Class 2. A hard drawn tube with excellent bending qualities.

This category contains a variety of compression fittings, including caps, sleeves, nuts, unions, tees, and elbows, manufactured by Jones Stephens Corp.

Recommended for use with both capillary soldered fittings and. The tube is identified by brown end caps, and markings every.

We have the largest selection of copper fittings available on the web. We offer competitive pricing on all copper fittings. Marley offer a wide range of soil systems, from PVCu push-fit & solvent weld for domestic drainage to HDPE & Acoustic soil for commercial applications. How to connect copper pipe with quick connect fittings. No soldering or compression needed.

Working. Pressure. Class 3(MPa)Max(mm)Min(mm)1. Class 3. A heavy walled tube used underground under special conditions. The tube is identified by markings every half metre .

It is emphasized that Class 0 tubing is hard drawn and any change of direction should be made. Local annealing of Class 0 in order to produce a bend is not recommended. When comparing two smooth- wall materials, such as copper and polypropylene, internal diameter.

Incorrect use or selection can lead to serious problems in relatively short periods of time. This is to allow for the expansion and contraction of the pipes during operation of the system.

For a tube of this quality, 1. It is further recommended that tubes be taped with Denso tape.

An additional corrosion mechanism falling within the realms of galvanic corrosion should be. Copper and galvanised sheeting for.

When steel, aluminium or zinc is put in contact with a copper metal, the corrosion rate of the. Galvanic corrosion between two metals is seldom a significant problem because the. Galvanic series generally refer to metals and alloys under specific conditions. Bursting, for example, does not occur at the first part to freeze, on the contrary.

Under these conditions the relative bursting point of a galvanized iron. This is the most widely used of the solders, and it is the most cost. Dirty or contaminated fluxes should be discarded to prevent poorly soldered joints.

Ensure all burrs are removed. Clean tube end and fitting, if required, to remove any dirt, plaster, tape glue etc by means of a. Apply Maksal. It is good practice to also apply flux to the inside of the fitting. To assist, refer to Table 6, which shows recommended lengths of solder to be used for the.

It is recommended that this table is used and the solder bent at right angles and. Apply the flame to the assembled joint concentrating the heat at the centre of the fitting rather. CAUTION: DO NOT MELT THE SOLDER WITH THE FLAME! The tube and fitting should be heated sufficiently to melt the solder when applied without the use. An indication of overheating is when the. The recommended use of water soluble fluxes such as Maksal. If a system is to be inoperative for any extended period after.

Capillary fittings with short sockets should not be used for soft soldering. Soldering of these sizes can also be achieved in any position if the correct procedure is. Finally bring the torch to about the “7 o’clock” position. Once the solder has solidified, the joint area should be wiped with a damp rag to remove. Pressure ratings should therefore be calculated as for annealed tubing and care taken to. These are alloys containing silver and alloys. Fluxes are not normally required when joining copper to copper only when joining.

Check with recommendations of the filler material manufacturer. Excess fuel. It isadvisable to allow the fitting to cool naturally after brazing. It is not. recommended by Maksal. DO NOT over tighten the cap nuts. Recommended heat source LP Gas and indiction air rather than oxy- acetylene. Maksal. Inherent in this a reduced possibility of leaks and substantial installation costs. Thisprincipal applies equally to the overall use of copper tubing and any of the recommended.

Correct procedures learnt and applied produces professional workmanship and. Major points covered are. Specifications for Copper TubePerformance of Copper Tube. Joining of Copper TubeThe Capillary Solder System.

Copper Fittings , Elkhart Copper Fittings , Copper Pipe Fittings , Copper Fittings Specialist. Copper fittings are used in hot and cold water lines in plumbing systems when making connections to copper pipe. There are two basic types of copper pipe or tubing: rigid and flexible. Copper fittings can be used with both types of copper pipe. Rigid pipe is generally installed in new homes and provides a neater installation. Flexible copper pipe is best for repair work since it can be run around obstacles without connections or cuts. Solder is a fusible metal alloy that, when melted, joins two or more metals together in a process known as soldering.

The connections produced by solder are liquid and gas tight. Soldering a copper fitting with debris on it will result in a poor seal.

Using a Tu- Turn copper fitting brush will ensure a clean copper fitting. Flux will keep the copper from oxidizing when heated. This provides a firm bond between the copper and the solder. A quality soldering iron is needed to join the copper pipe and the fitting. Once the copper fitting has been properly prepared, it can be bonded to a copper pipe by using a quality soldering torch. These fittings are connected directly to a copper pipe.

Unlike a standard elbow, a street elbow is connected to a copper fitting. They are also used to connect pipes of different diameters or for changing the direction of pipe runs. However, a union is designed to allow quick and convenient disconnection of pipes for maintenance or fixture replacement.